The advantages of the shredder and the introduction of related problems
Nowadays, the problem of environmental pollution is becoming more and more serious, and our non-renewable resources are becoming less and less. Therefore, in order to protect the environment and reduce the cost of resources, we strongly emphasize the recycling of resources. In this process, the shredder is an important processing equipment. Let's take a closer look at "the advantages of the shredder and the introduction of related issues".
[The necessity of knowing the wear and tear of the shredder]
The shredder can see whether the shredding meets the standard by seeing the sharpness of the knife, but the accumulated work of the blade will gradually become dull from sharp, but it is also necessary to consider the emergency situation leading to edge damage. The sharpened appearance is usually normal wear, the second most likely broken edge is called abnormal wear.
Whether it is normal wear or abnormal wear, it has a great impact on the production process. As the saying goes: sharpening knives does not make a mistake in chopping wood. Only by mastering the wear of the knives can the knives be replaced in time, thereby ensuring the normal production progress. The shredder is obviously abnormally worn, and the tool change time is abnormally worn. Then the process of normal wear and tear, how do you know the wear level of the tool we need to replace? We need to know the increase in the uptime of the shredder, the wear.
The first stage: also known as the initial wear stage. Due to the rough surface of the new equipment tool is not smooth, there are some small wrinkles, oxide or carbon layers and a series of defects. The equipment has sharp edges, the blade surface in contact with the surface is not very large, the greater the pressure, so this stage of tool wear is also called during the operation of the equipment. This stage is not recommended to replace the tool, because it is the time when the equipment performance reaches the operating cycle, which can create value.
Stage 2: This is the normal wear and tear of the tool during the break-in period. After a stage, the rough surface basically polishes the knife, and the knife has started to wear, but slowly because it is on an unprecedentedly sharp edge. Therefore, under normal operating conditions, the wear stage of the shredder equipment is very stable and slow.
Stage 3: This is an important stage and requires close attention to the wear state of the blade. If the width of the wear band expands to a certain limit, the surface roughness, cutting force and cutting temperature increase rapidly, and the wear rate increases rapidly, causing the tool to fail and lose its cutting ability. In the rational use of production tools to ensure the quality of processing, one stage of wear should be avoided. Before this stage arrives, it is necessary to change the tool or replace the blade in time.
[What are the advantages of the new shredder equipment]
At present, science and technology are developing rapidly, especially in the machinery industry, intelligence and assembly line operations have become a development trend. Nowadays, more and more intelligent equipment is used, which not only saves human resources, but also greatly improves production efficiency. The new shredder integrates the advantages of all shredders, all of which are controlled by microcomputer, and have reached a fully intelligent level.
The advantages of the new shredder equipment are:
1. Thick and heavy moving knives, high crushing power, all knives are made of alloy steel, sturdy and long service life.
2. The frame plate is thick, can resist high torque, and is very strong.
3. It adopts microcomputer (PC) automatic control, and has the functions of start, stop, reverse and overload automatic reverse control.
4. The equipment has the characteristics of low speed, high torque, low noise, and dust that can meet environmental protection standards.
5. Easy to adjust, low maintenance cost, economical and durable.
6. The thickness of the tool and the number of claws can be changed according to different materials.
7. The equipment design does not have the concept of sieve bottom. The material is fed from the upper silo and directly discharged from the lower silo after passing through the crushing silo, so it has the advantage of high production efficiency.
8. With advanced automatic control system, low speed, high torque, low noise and low dust.
9. Hydraulic pushing system, forced feeding structure of swing arm, 80° turning over, higher utilization rate of cutter body, never jamming.
The above introduction on "the necessity of knowing the wear condition of the shredder" and "what are the advantages of the new shredder equipment", I hope it will help you understand the "introduction of the advantages of the shredder and its related problems".
Recommend products
CONTACT US:
If you have any requirement or suggestion, please fill in the form and send to us, thanks!E-mail:sunymachine@gmail.com | Whatsapp:+8613674945231
